曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
2 - Lever
3 - L.H. support
4 - Cotter pin
5 - Pin
6 - Central spacer
7 - Rivet
8 - Attachment (bolt, washer, nut)
9 - Fitting doubler
10 - Lever
11 - R.H. support
Frame - Flight control rear support on frame C9
Figure 801
WA
Validity : S / N 1 - 450 53 20-01Page 804
(BA) SEP 04
PAGE INTENTIONALLY LEFT BLANK
2 - Lever
8 - Attachment (bolt, washer, nut)
10 - Lever
12 - Bolt
13 - Washer
14 - Nut
15 - R.H. unfolding wedge
16 - L.H. unfolding wedge
17 - Bolt
18 - L.H. support
19 - Spacer
20 - Nut
21 - Spacer
22 - Cotter pin
23 - Pin
24 - Washer
25 - Bolt
26 - Additional lower attachment
27 - L.H. doubler
28 - Lower fitting
29 - Bolt
30 - Washer
31 - Nut
32 - R.H. doubler
33 - Spacer
34 - Spacer
35 - R.H. support
I Frame - Installation of flight control rear support on frame C9
Key to Figure 802
AAAA
Validity : S / N 1 - 450 Page sEp80046
53 20 01 (BA)
Frame - Installation of flight control rear support on frame C9
Figure 802
AAM
Validity : S / N 1 - 450 53-20-01 Page 807
(BA) SEP 04
PAGE INTENTIONALLY LEFT BLANK
AAAA
Validity : S / N 1 - 450
Page 808
53-20-01
(BA) SEP 04
SKINS
REPAIR
1. REPAIR / REPLACEMENT - SKIN BETWEEN FRAMES C5 AND C9
A. Tools and consumable materials
- Sealant (TB 09-002A)
- Sealant (TB 09-001A)
B. Procedure
NOTE : When a skin is replaced between frames C5, C6, C7, C8 and C9, apply some sealant (TB 09-001A) to rivets and between the skin and frames - refer to 20-00-09.
NOTE : When a skin is replaced between frames C5, C6, C7, C8 and C9, apply a sealing bead with I sealant (TB 09-002A) at the skin junctions - refer to 20-00-09.
AAAA
Validity : S / N 1 - 9999 53 20-03Page 801
(BA) SEP 04
PAGE INTENTIONALLY LEFT BLANK
WA
Validity : S / N 1 - 9999
53-20-03 Page 802
53
(BA) JUN 01
FAIRINGS
REMOVAL / INSTALLATION
1. REMOVAL OF THE TAIL CONE (Figure 401)
A. Tools and consumable materials
None
B. Procedure
Pre-MOD. 151 - refer to Detail B
1) If the rear light is installed, open navigation light and anticollision light switch-breakers.
2) Hold tail cone (3).
3) Remove screws (5) and washers (4).
4) If the rear light is installed, disconnect connectors (1).
5) Remove tail cone (3).
Post-MOD. 151 - refer to Detail A
1) Hold tail cone (3).
中国通航网 www.ga.cn
通航翻译 www.aviation.cn
本文链接地址：TB20 MAINTENANCE MANUAL 53 机身 TB20飞机维护手册(13)
|
