|
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
4) Engage lever (33) equipped with spacer (32) on actuator rod (51) and install bolt (31), washer (34) and nut (36). 5) Safety with a new cotter pin (35). ACAC Validity : S / N 1 - 9999 27 30-03Page 403 (CA) SEP 02 6) Install turnbuckles (38) on the cables with immobilization tool (42). 7) Remove cable clamps (52). 8) Adjust the tension of the cables - refer to Page 501. 9) Lockwire turnbuckles (38). 10) Check the travel of the elevator trim tab - refer to Page 501. G. Disassembly of rear and front cables (Figures 401, 403 and 404) 1) Remove cable clamp (52) from rear reel (54). 2) Remove and discard cotter pin (57) ; remove nut (58) and washer (56). 3) Unscrew actuator rod (51) from rear reel (54). Actuators without shims - see Figure 403, Detail B 4) Remove rear reel (54), then unwind and remove rear cable (39). 5) If necessary, remove and discard cotter pins (63), remove nuts (53), external washers (61) and spacers (60). 6) Push out bolts (62) ; remove support (59), washers (61) and bolts (62). Actuators with shims - see Figure 403A, Detail B 4) Clear lockwasher (66) tabs, remove bolts (67), lockwashers (66), actuator bearings (68) and shim(s) (65) (if installed) ; discard lockwashers (66). 5) Remove rear reel (54), then unwind and remove rear cable (39). 6) If necessary, remove and discard cotter pins (63), remove nuts (53), external washers (61) and spacers (60). 7) Push out bolts (62), remove support (59), washers (61) and bolts (62). Actuators Post-MOD. 148 - see Figure 403B, Detail B 4) Clear lockwasher (66) tabs, remove bolts (67), lockwashers (66), actuator bearings (68) and shim(s) (65) (if installed) ; discard lockwashers (66). 5) Remove and discard seals (69) from actuator bearings (68). 6) Remove rear reel (54), then unwind and remove rear cable (39). 7) If necessary, remove and discard cotter pins (63), remove nuts (53), external washers (61) and spacers (60). 8) Push out bolts (62) ; remove support (59), washers (61) and bolts (62). All 9) Remove cable clamp (52) from front reel (1). 10) Unwind and remove front cable (27) from around front reel (1). ACAC Validity : S / N 1 - 9999 27 30-03Page 404 (CA) SEP 02 H. Assembly of front cable (Figures 401,404 and 405) NOTE : . Two operators are required to perform these operations. . Cable "L.H. threaded" end fittings are matchmarked by side notches on the 6 flats of the hexagonal nuts. . Inspect cables and pulleys for condition - refer to 20-00-07. . Lubricate the cables in the winding area with grease (TB 04-004A). 1) Wind front cable (27) [Length 28.26 ft (8615 mm)] around front reel (1) - see Figure 405, Detail D. a) Position front reel (1) as illustrated in Detail D, Figure 405, between the jaws of a vice (protected jaws) at moderate clamping pressure. 中国通航网 www.ga.cn 通航翻译 www.aviation.cn 本文链接地址：TB20 MAINTENANCE MANUAL 27 FLIGHT CONTROLS TB20飞机维护手册 飞行操纵(42) |
