曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
length
L (mm) HUCK reference
Min. Max.
0.64 1.57 5.03 NAS 1919B - 04 - 01
1.58 3.17 6.60 NAS 1919B - 04 - 02
3.2 3.20 4.75 8.20 NAS 1919B - 04 - 03
4.78 6.35 9.78 NAS 1919B - 04 - 04
6.38 7.92 11.38 NAS 1919B - 04 - 05
7.95 9.52 12.95 NAS 1919B - 04 - 06
0.79 1.57 5.76 NAS 1919B - 05 - 01
1.58 3.17 6.68 NAS 1919B - 05 - 02
4.0 3.20 4.75 8.28 NAS 1919B - 05 - 03
4.78 6.35 9.85 NAS 1919B - 05 - 04
6.38 7.92 11.45 NAS 1919B - 05 - 05
7.95 9.52 13.03 NAS 1919B - 05 - 06
0.94 1.57 6.37 NAS 1919B - 06 - 01
1.58 3.17 7.29 NAS 1919B - 06 - 02
3.20 4.75 8.89 NAS 1919B - 06 - 03
4.8 4.78 6.35 10.46 NAS 1919B - 06 - 04
6.38 7.92 12.06 NAS 1919B - 06 - 05
7.95 9.52 13.64 NAS 1919B - 06 - 06
9.55 11.10 15.24 NAS 1919B - 06 - 07
11.12 12.70 16.81 NAS 1919B - 06 - 08
rty : S / N 1 - 9999 A alidi 51-40 02Page 212
(BA) SEP 04
14514002AAAAVZ4000 K
L
100° countersunk head 2.4 dia. "CHERRY NUT-PLATE" rivet, type CCR 264 SS
Grip range (mm) Rivet
length
L (mm) CHERRY NUT-PLATE
reference
Min. Max.
- 1.57 3.55 CCR 264 SS - 3 - 1
1.60 3.17 5.15 CCR 264 SS - 3 - 2
3.20 4.75 6.73 CCR 264 SS - 3 - 3
4.77 6.35 8.33 CCR 264 SS - 3 - 4
6.37 7.92 9.90 CCR 264 SS - 3 - 5
7.95 9.52 11.50 CCR 264 SS - 3 - 6
9.55 11.12 13.08 CCR 264 SS - 3 - 7
11.15 12.70 14.68 CCR 264 SS - 3 - 8
E. Drilling diameters (for countersunk rivets, see Paragraph G.)
NOTE : Theoretically, the material remaining between the hole and the part edge(s) must have a minimum dimension of 1.5 time the hole diameter. After repair (drilling to the upper diameter) and in any case, this minimum dimension will be smaller to one time the new hole diameter).
1) Solid rivets
a) For standard thicknesses : nominal dia. +0.2 ; +0
b) For large thicknesses : nominal dia. +0.1 ; +0
The rivet should be a tight fit.
2) Blind rivets
Nominal dia. (+0,2 ; +0)
F. General advice for riveting (for countersunk rivets, see Paragraph G.)
中国通航网 www.ga.cn
通航翻译 www.aviation.cn
本文链接地址:TB20 MAINTENANCE MANUAL 51 标准施工/结构 TB20飞机维护手册(18)
|